Crystal
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Crystal


Home >> Homeware >> Crystal

What Is A Crystal? And How To Test It

Crystal are use to keep the frequency of the clock from drifting. If the signal from this clock stops, or is weak, or the pulses begin to vary, the electronic equipments might show intermittent faults or might stop altogether. The microprocessor pins that hold the crystal are usually called OSC IN and OSC OUT as shown in Figure 1 and the frequency is marked on the crystal. Typical examples of crystal oscillator frequency are 3.58MHZ, 4MHZ, 8MHZ, 24MHZ etc.

Testing Crystal Crystals are quite fragile components because of their construction. Unlike a resistor or capacitor, if you drop one on the ground from a decent height, its 50-50 bet whether it will work again. Testing the crystal is not a breeze either. You cannot just take out your trusty multimeter and plug the crystal in it. In fact, there are three right ways to test a crystal: -

(a) Using Oscilloscope A crystal produces a sine wave when excited. It is appropriate then, to see a waveform representative of a sine wave on the clock pins. If the clock is not functioning properly, replace the crystal. In most cases this should solve the problem since microprocessors are usually very reliable. Check the crystal with power on.

(b) Frequency Counter Frequency Counter can be use to check the frequency of the crystal. The reading must be taken when the equipment power is switch “on”. Place the probe of frequency counter to the crystal pin and read the measurement. Be sure that your frequency counter meter has the range that is higher than the crystal frequency you are measuring.

(c) Crystal Checker With this method, usually the crystal is placed in the feedback network of a transistor oscillator. If it oscillates and the LED is lighten up, this mean that the crystal is working. If the crystal doesn’t work, the LED stays off. Instead of using LED, some other crystal checker uses a panel meter to indicate if the crystal is working or not.

By Jestine Yong | Posted on 2007-07-02 01:57:15

About The Author:

Jestine Yong is a electronic repairer and writer. For more information about electronic repair please visit his website at http://www.noahtec.com/

Definition:

In chemistry and mineralogy, a crystal is a solid in which the constituent atoms, molecules, or ions are packed in a regularly ordered, repeating pattern extending in all three spatial dimensions.

The word crystals originates from the Greek word "Krystallos" meaning clear ice, and once referred particularly to quartz, rock crystal.

Most metals encountered in everyday life are polycrystals. Crystals are often symmetrically intergrown to form crystal twins.

More Articles for "Crystal":


We Value Your Feedback

It is with your comments and suggestions that we can better meet the needs of our site visitors, so please don't hesitate to contact us.

Your Name:

Your E-mail Address:


Your Message:



Source: Articles from Golden-Info.com

Home Page / Contact Us / Privacy Policy / Disclaimer / Site Map / Link To Us

Copyrighted 2008-2011 By Golden Info. All Rights Reserved.